Just How to Remove as well as Replace a Tub.
Just How to Remove as well as Replace a Tub.
Blog Article
Presented here below you will find some decent insight with regards to How to Install a Bathtub.
Setting up a tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a brand-new one is also a moderately challenging job. If the old bathtub is easily easily accessible, the task can relocate easily; if you need to open up a wall surface to get rid of the old tub as well as position the new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly require a helper to vacate the old bathtub as well as set in the new one. See to it you have actually qualified yourself for the work and also are comfortable attempting it. Rather than working with a professional to take over a halfway-completed task, it is far better to think about employing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will help you install a brand-new tub in your restroom if you have actually currently purchased a brand-new tub and do not need to change the arrangement of your previous water system pipes.
Your devices as well as material list ought to comprise the following:
Planning for the Setup
Firstly, the supporting frame provided with the bath must be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently be ready to be suited its final setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the restricted gain access to that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will come from the pipelines. As soon as the supply pipes have been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Before moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in evenly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level as well as adjusting the feet on the bath tub till the level checks out level.
To install faucets, fit all-time low of the outermost versatile tap adapter to the ideal supply pipe by making a compression sign up with; then do the same for the other tap.
Switch on the water and also examine all joints and also brand-new pipework for leaks and tighten them if required. Load the tub and also check the overflow outlet and also the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the bathtub should wait till the tub has been used at the very least when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Safeguard the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type must be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture an inflexible seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about complications with dampness as well as feasible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to allow for the movement experienced when the tub is in usage. The sealant can split rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly offered on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that report on Installing A Bathtub through someone on our other website. Liked our content? Please share it. Let someone else check it out. Thanks so much for going through it.
Estimate Report this page